Torn Window Screen: Patch It, Rescreen It or Replace It?
A small hole or short tear in an otherwise good screen can be patched. A bigger tear, several holes, or mesh that is brittle or sagging means new mesh in the same frame, called rescreening. Only a bent frame, a broken corner or a screen that no longer fits needs a whole new screen. Here is how to tell which one you need, and how to do the easy fixes yourself.
- Screens rescreened and made to size across the DMV
- Free estimates
- Hablamos español
Patch, rescreen or replace: what you need
Take the screen out and look at it on a flat surface. Check the mesh, the rubber spline that holds it in, the frame and the corners.
| What you see | The fix | DIY or call? |
|---|---|---|
| A small hole or short tear, mesh still tight | Patch it | Easy DIY with a patch kit |
| A long tear, or several holes | Rescreen: new mesh and spline in the same frame | DIY on a small window screen; call for large or many screens |
| Mesh brittle, faded or sagging all over | Rescreen | Same as above |
| Mesh popping out at the edges | New spline; the old one has shrunk or dried out | Easy DIY |
| Frame bent, corner broken, screen loose in the opening | New frame cut to size, with new mesh | Call |
| Sliding screen door torn, off its track or dragging | Rescreen, new rollers, or a new door frame | Call, unless it is only the mesh |
DIY guides put the patch cutoff at a hole of about 2 to 3 inches. Past that, a patch tends to pull and the tear keeps growing, so rescreening is the better fix.
Why a small hole is worth fixing now
A small hole lets in insects all season, and it grows each time the window is opened or the screen is pushed. The CDC’s “Fight the Bite” advice on mosquitoes tells people to check for and repair holes in window and door screens.
One safety point: a screen keeps insects out, it does not keep a child in. It is not built to hold anyone’s weight, so keep furniture away from windows that open and use window guards or stops where young children play.
How to patch a small hole
For fiberglass or aluminum mesh with a hole or short tear and the rest still tight.
1. Clean and trim
Brush off dust and trim loose strands so the edges of the hole are neat.
2. Cut a patch
Use a patch from a screen repair kit, or a piece of matching mesh, a little bigger than the hole on every side.
3. Fix it on
Press a self adhesive patch on, or for aluminum mesh bend the patch wires through the screen and fold them over. Clear glue around the edge works on fiberglass.
4. Check it
Put the screen back and look from outside. A patch that lifts or pulls means the screen needs rescreening.
How to rescreen a window screen yourself
Worth doing on a standard window screen with a straight frame. You need new mesh, new spline in the same size as the old one, a spline roller and a sharp utility knife.
1. Pull the old spline
Lift one end of the rubber spline out of the groove and pull it all the way round. Take out the old mesh.
2. Lay the new mesh
Lay the frame flat and the mesh over it, with a margin on every side. Clamp or weight the frame so it does not bow.
3. Roll in the spline
Start at a corner and roll the mesh and new spline into the groove, one side at a time, keeping the mesh snug but not drum tight.
4. Trim
Cut off the extra mesh just outside the spline with the blade angled away from the screen.
Pulling the mesh too tight bows the frame inward, and then the screen will not sit in the window. Tight enough to remove wrinkles is enough.
When to hand it over
DIY stops making sense when the frame is the problem, or the job is bigger than one window screen.
A bent frame will not hold mesh tight or sit in the window. It needs a new frame cut to size.
Large, heavy to handle flat, and often dragging on worn rollers too. The door glass and track are worth a look at the same time.
Many screens at once
A whole house of torn or faded screens is faster done in one visit, with the same mesh on every window.
A different mesh
Pet resistant, solar or fine mesh is stiffer and harder to roll in neatly than standard fiberglass.
We rescreen frames, make new screens to size and repair sliding screen doors: window and door screen repair. Other window problems while we are there: drafty window repair and all window repair.
- A photo of the whole screen and a close photo of the damage
- The width and height of the screen frame
- How many screens, and whether any are sliding screen doors
Torn window screen questions
More questions? Read will a screen keep a child from falling and why a window won’t stay open, browse our glass repair FAQ or contact us.
How big a hole in a window screen can be patched?
Small holes and short tears in mesh that is otherwise tight. DIY guides put the cutoff at about 2 to 3 inches; past that, rescreening the frame is the better fix.
What does rescreening a window screen mean?
Taking the old mesh and rubber spline out of the frame and rolling in new mesh with new spline. The frame stays the same.
When does a window screen need a new frame?
When the frame is bent, a corner is broken, or the screen no longer sits tight in the window. New mesh will not stay tight in a bent frame.
Why does the mesh keep popping out of my screen?
The rubber spline has shrunk or dried out and no longer grips. Replace the spline, in the same size, and the mesh will hold.
Can a window screen stop a child from falling out?
No. Screens are made to keep insects out and are not built to hold a person’s weight. Use window guards or stops on windows young children can reach.
Screens to fix?
Send a photo of the screen and its size, or call (202) 600-6220 for a free estimate.