Open 24/7Licensed in VirginiaInsured and bonded

Call (202) 600-6220

How to Clean Coated Glass, Low-E Windows and Coated Shower Glass, Without Damaging It

Clean coated glass with plenty of water, a mild soap or a plain glass cleaner, a soft cloth or a clean squeegee, and dry it gently. Never use razor blades, steel wool, scouring pads, abrasive powders or strong acids on it. In most double pane windows the low-E coating is sealed between the panes, so you never touch it; the surfaces you clean are plain glass. Here is how to tell which side of your glass is coated, and how to care for each kind.

First, find out where the coating is

Coatings sit on different surfaces depending on the glass. That decides how careful you need to be.

Most low-E today is a soft coat on one of the two inside surfaces of the sealed unit. You cannot reach it. Clean the outside and the room side like any glass, gently.

Hard coat low-E on an open surface

Some windows, storm panels and single pane glass have a hard coat low-E on a surface you can touch, often the room side. It is durable but scratches more easily than plain glass, and it can look hazy if cleaned with the wrong product.

Many shower doors have a factory coating on the inside face that makes water bead and slow mineral buildup. It is thin and wears off faster with harsh cleaners.

Tint, privacy and security films are a plastic layer on the room side. Treat them as the softest surface of all.

A quick test for a coating

At night, hold a small light or a lit match near the glass and look at the reflections. Plain glass shows reflections that are all the same color. A low-E coating shows one reflection in a different tint, often pink, green or blue, and its position tells you which pane it is on. If the odd colored reflection is the one nearest you on the room side, the coating is on the surface you clean. Dew on the outside of the glass is something else: condensation on the outside of windows.

For shower glass, ask whoever installed it, or look for water that still beads on the inside face but not the outside. If you are not sure, treat the glass as coated. Gentle cleaning works on plain glass too. Why low-E is used at all: is low-E glass worth it.

How to clean it, step by step

The same method works on windows and shower glass. Do it out of direct sun, so the glass does not dry with streaks.

1. Rinse first

Flood the glass with clean water to float off grit. Wiping dry dust across a coating is how most fine scratches happen.

2. Wash gently

Use warm water with a little mild dish soap, or a plain glass cleaner, on a soft microfiber cloth or a clean sponge.

3. Rinse again

Clear all the soap off with clean water.

4. Dry with a clean squeegee or cloth

Use a squeegee with a soft, undamaged rubber blade, or a dry lint free cloth. Change the cloth when it gets gritty.

What never to use on coated glass

This list protects plain glass too.

Never useWhy
Razor blades or metal scrapersCut straight through a coating and leave marks that do not come out
Steel wool, scouring pads, the green side of a spongeScratch coatings and film, and leave haze on hard coat low-E
Abrasive powders or cream cleansersWear a shower coating away and dull the glass
Strong acids and harsh descalersCan attack coatings; use them only if the glass maker allows it
Pressure washers up closeCan drive grit across the glass and push water past window seals
Two cleaners mixed togetherSome mixes give off dangerous fumes; see below

Do not mix cleaners

Shower glass often gets a mildew spray one day and a glass cleaner the next, and some of those contain bleach and some contain ammonia. The CDC’s guide to cleaning and sanitizing with bleach says never to mix bleach with ammonia or any other cleaner. Use one product, rinse it off completely, and only then use another, with the bathroom fan on.

Hard water spots on shower glass need their own method: see how to remove hard water stains from a glass shower door. If the glass has a coating, start with the gentlest step in that post and stop there if it works.

Dirt, or damage?

Some marks on coated glass are not dirt, and more cleaning will not help.

Fine scratches that catch the light

Usually from grit or a scraper. On a coated surface they cannot be polished out without removing the coating. See can scratched glass be fixed.

Haze that comes back after every clean

On a shower door, it can be etching from minerals; on hard coat low-E, residue from a product that does not suit it. Try plain water and a soft cloth before anything stronger.

Water no longer beads on shower glass

The factory coating has worn off. The glass is fine; some coatings can be reapplied, or you clean it as ordinary glass.

Fog or streaks you cannot reach

If the mark is between the panes, it is not on any surface you can clean: the seal has failed. See double pane glass replacement.

Glass damaged beyond cleaning?

When coated glass is scratched, etched or fogged inside, the glass can usually be replaced without changing the window frame or the shower door hardware. We replace window and shower glass across Northern Virginia and Maryland.

PHOTO NEEDED (only admins see this): close up of a low-E double pane window being cleaned with a soft cloth and squeegee, and coated shower glass with water beading. Landscape 1600x1000, WebP.

Cleaning coated glass questions

Yes, a plain glass cleaner or mild soap and water is fine. In most double pane windows the low-E coating is sealed between the panes, so you never touch it. Avoid abrasive cleaners, razor blades and strong acids on any coated surface.

At night, hold a small light near the glass and look at the reflections. A low-E coating shows one reflection in a different tint, and its position tells you which pane it is on.

No. A razor blade or metal scraper cuts through the coating and leaves marks that cannot be removed. Soak stubborn spots with water and mild soap and use a soft cloth instead.

Rinse with water, wash with a mild soap on a soft cloth or sponge, rinse again and squeegee. Avoid abrasive powders, scouring pads and harsh descalers, which wear the coating away.

The factory coating that makes water bead has worn off, often from harsh or abrasive cleaners. The glass is still fine and can be cleaned as ordinary glass.

Coated glass scratched or hazy?

Send a photo of the glass, or call (202) 600-6220 for a free estimate.