Cracked or Missing Glazing Putty on Old Wood Windows: What It Means and How Windows Are Reglazed
Cracked or missing glazing putty means the seal on the outside of the glass has failed, so rain can get behind it and into the wood of the sash. A few small cracks can be patched; putty that is loose, falling out or lets the glass rattle needs the sash reglazed: old putty out, glass bedded, new points and new putty, then paint. Here is how to read what you see, and how the work is done.
- Old window glass work across the DMV
- Free estimates
- Hablamos español
What glazing putty does
In an old wood window, each pane sits in a shallow groove in the sash called the rabbet. Small metal glazing points pressed into the wood hold the glass in place. The putty is the sloped bead on the outside that covers the points and the edge of the glass.
Its job is to shed water. Rain hits the putty and runs off the glass and away from the wood. Once the putty cracks or lets go, water gets into the gap, sits against the bare wood of the rabbet and starts to rot the sash. That is why failed putty matters more than its looks suggest. Weighing an upgrade from single glass? See single pane vs double pane: is upgrading worth it.
What each sign means
Look at the putty from outside on a dry day. Press it gently with a thumbnail and push lightly on the glass.
| What you see | What it means | What to do |
|---|---|---|
| Hairline cracks, putty still hard and stuck on | The surface has dried out, but the putty still sheds water | Clean, prime and paint; keep an eye on it |
| A short section cracked through or missing | Water can get behind the putty at that spot | Cut out that section, prime the wood and patch it with new putty |
| Putty loose along a whole side, or coming out in chunks | The bond to the wood has gone; more will follow | Reglaze that pane all the way round |
| The glass rattles or moves when you press it | The putty and points are no longer holding the pane | Reglaze soon; a loose pane can fall out or crack |
| Bare, gray or soft wood where the putty used to be | Water has been getting in for a while | Check for rot before reglazing; soft wood has to be repaired first |
| Putty has fallen out and the glass is cracked too | The pane and the seal both need replacing | New glass, cut to size, set in fresh putty |
Patch it or reglaze the whole sash?
A patch is enough when
- Only a short section is cracked through or missing
- The rest of the putty is hard and firmly stuck
- The glass does not move when you press it
- The wood under the missing section is sound
Reglaze the sash when
- Putty is loose or falling out on more than one side
- Panes rattle in the wind
- You are stripping and repainting the window anyway
- Patches have been done before and keep failing next to each other
On a sash with several small panes, it is common to reglaze only the panes that need it and patch the rest. There is no need to strip sound putty just to make it all new.
How a window is reglazed
The same steps apply whether we do it or you do. The care is in not cracking old glass and not gouging the wood.
1. Soften and remove the old putty
Old putty is often rock hard. It is softened with gentle heat and lifted out with a putty knife, working with the wood, not against the glass.
2. Pull the points and clean the rabbet
The old glazing points come out, and the groove is scraped clean down to sound wood.
3. Prime the bare wood
Bare wood soaks the oil out of new putty and makes it fail early. Primer or oil on the rabbet first.
4. Bed the glass
The rabbet gets a thin layer of fresh compound first, and the glass is pressed into it so it sits evenly with no rattle.
5. Set new points
New glazing points are pressed into the wood on every side to hold the pane.
6. New putty, tooled to a bevel
The final bead is tooled to a clean slope so water runs off the glass, then painted once it has skinned over, with the paint lapping slightly onto the glass to seal the edge.
Older homes: think about lead paint before you scrape
If your home was built before 1978, the paint and old putty on its original windows may contain lead. The EPA warns that a renovation, repair or painting project in a pre-1978 home that has lead-based paint can easily create dangerous lead dust.
If your house is that old and you plan to strip putty yourself, read the EPA’s guidance first, keep the work wet rather than dry sanding, keep children and pets away and clean up carefully. If you would rather not do it, ask any contractor you hire how they handle older paint before the work starts.
When to do it yourself and when to call us
Patching a short section on a ground floor window is a reasonable weekend job. For a whole broken pane, see can I replace a broken window pane myself. It makes sense to hand it over when:
- The glass is cracked or broken as well as the putty
- The windows are upstairs and can only be reached from a ladder
- The sash has many small panes, or old wavy glass you do not want to risk cracking
- There is soft or rotted wood under the putty
- The window is stuck, painted shut, or the sash cords are broken too
We cut new glass to size and reglaze old wood sashes for homes across Northern Virginia and Maryland: see single pane glass replacement. Sash that will not stay up? That is window balance repair. Drafts around the sash are covered on drafty window repair, and the rest of our window work is on window repair.
Glazing putty questions
More questions? Read why a window won’t stay open and fixing a drafty window without replacing it, browse our glass repair FAQ or contact us.
Is cracked glazing putty a problem?
Fine surface cracks on putty that is still hard and stuck on are mostly cosmetic; prime and paint it. Cracks that go right through, or putty that is loose or missing, let water get behind it into the wood of the sash, and that is what causes rot.
Can I patch glazing putty instead of redoing the whole window?
Yes, if only a short section has failed and the rest is hard and firmly stuck. Cut out the failed part, prime the bare wood and fill it with new putty. If putty is loose on several sides or the glass rattles, reglaze the pane all the way round.
Why is my old window glass rattling?
The putty and the small glazing points that hold the pane have let go. The glass should be bedded and reglazed before it cracks or falls out.
Do I need to prime wood before glazing a window?
Yes. Bare wood draws the oil out of fresh putty, which makes it dry out and crack early. Prime or oil the rabbet first, then bed the glass and apply the putty.
Can you reglaze old wood windows without replacing the glass?
Yes. The old putty and points come out, the original glass is cleaned and bedded again, and new points and putty go in. Only cracked or broken panes need new glass.
Old windows losing their putty?
Send a photo of the sash from outside, or call (202) 600-6220 for a free estimate.