Open 24/7Licensed in VirginiaInsured and bonded

Call (202) 600-6220

Cracked or Missing Glazing Putty on Old Wood Windows: What It Means and How Windows Are Reglazed

Cracked or missing glazing putty means the seal on the outside of the glass has failed, so rain can get behind it and into the wood of the sash. A few small cracks can be patched; putty that is loose, falling out or lets the glass rattle needs the sash reglazed: old putty out, glass bedded, new points and new putty, then paint. Here is how to read what you see, and how the work is done.

What glazing putty does

In an old wood window, each pane sits in a shallow groove in the sash called the rabbet. Small metal glazing points pressed into the wood hold the glass in place. The putty is the sloped bead on the outside that covers the points and the edge of the glass.

Its job is to shed water. Rain hits the putty and runs off the glass and away from the wood. Once the putty cracks or lets go, water gets into the gap, sits against the bare wood of the rabbet and starts to rot the sash. That is why failed putty matters more than its looks suggest. Weighing an upgrade from single glass? See single pane vs double pane: is upgrading worth it.

What each sign means

Look at the putty from outside on a dry day. Press it gently with a thumbnail and push lightly on the glass.

What you seeWhat it meansWhat to do
Hairline cracks, putty still hard and stuck onThe surface has dried out, but the putty still sheds waterClean, prime and paint; keep an eye on it
A short section cracked through or missingWater can get behind the putty at that spotCut out that section, prime the wood and patch it with new putty
Putty loose along a whole side, or coming out in chunksThe bond to the wood has gone; more will followReglaze that pane all the way round
The glass rattles or moves when you press itThe putty and points are no longer holding the paneReglaze soon; a loose pane can fall out or crack
Bare, gray or soft wood where the putty used to beWater has been getting in for a whileCheck for rot before reglazing; soft wood has to be repaired first
Putty has fallen out and the glass is cracked tooThe pane and the seal both need replacingNew glass, cut to size, set in fresh putty

Patch it or reglaze the whole sash?

A patch is enough when

Reglaze the sash when

On a sash with several small panes, it is common to reglaze only the panes that need it and patch the rest. There is no need to strip sound putty just to make it all new.

How a window is reglazed

The same steps apply whether we do it or you do. The care is in not cracking old glass and not gouging the wood.

1. Soften and remove the old putty

Old putty is often rock hard. It is softened with gentle heat and lifted out with a putty knife, working with the wood, not against the glass.

2. Pull the points and clean the rabbet

The old glazing points come out, and the groove is scraped clean down to sound wood.

3. Prime the bare wood

Bare wood soaks the oil out of new putty and makes it fail early. Primer or oil on the rabbet first.

4. Bed the glass

The rabbet gets a thin layer of fresh compound first, and the glass is pressed into it so it sits evenly with no rattle.

5. Set new points

New glazing points are pressed into the wood on every side to hold the pane.

6. New putty, tooled to a bevel

The final bead is tooled to a clean slope so water runs off the glass, then painted once it has skinned over, with the paint lapping slightly onto the glass to seal the edge.

Older homes: think about lead paint before you scrape

If your home was built before 1978, the paint and old putty on its original windows may contain lead. The EPA warns that a renovation, repair or painting project in a pre-1978 home that has lead-based paint can easily create dangerous lead dust.

If your house is that old and you plan to strip putty yourself, read the EPA’s guidance first, keep the work wet rather than dry sanding, keep children and pets away and clean up carefully. If you would rather not do it, ask any contractor you hire how they handle older paint before the work starts.

When to do it yourself and when to call us

Patching a short section on a ground floor window is a reasonable weekend job. For a whole broken pane, see can I replace a broken window pane myself. It makes sense to hand it over when:

We cut new glass to size and reglaze old wood sashes for homes across Northern Virginia and Maryland: see single pane glass replacement. Sash that will not stay up? That is window balance repair. Drafts around the sash are covered on drafty window repair, and the rest of our window work is on window repair.

PHOTO NEEDED (only admins see this): an old wood sash with cracked and missing glazing putty, and the same sash after reglazing and painting, from a real job. Landscape 1600x1000, WebP.

Fine surface cracks on putty that is still hard and stuck on are mostly cosmetic; prime and paint it. Cracks that go right through, or putty that is loose or missing, let water get behind it into the wood of the sash, and that is what causes rot.

Yes, if only a short section has failed and the rest is hard and firmly stuck. Cut out the failed part, prime the bare wood and fill it with new putty. If putty is loose on several sides or the glass rattles, reglaze the pane all the way round.

The putty and the small glazing points that hold the pane have let go. The glass should be bedded and reglazed before it cracks or falls out.

Yes. Bare wood draws the oil out of fresh putty, which makes it dry out and crack early. Prime or oil the rabbet first, then bed the glass and apply the putty.

Yes. The old putty and points come out, the original glass is cleaned and bedded again, and new points and putty go in. Only cracked or broken panes need new glass.

Old windows losing their putty?

Send a photo of the sash from outside, or call (202) 600-6220 for a free estimate.